Voice coil size guide: inside diameter, former and winding height
A replacement voice coil is usually ordered by size: 1 inch, 2 inch, 3 inch and so on. In practice, the inch label is only a catalogue group. The part that fits is defined by three measurements — the inside diameter of the former, the former height and the winding height — plus the variant details behind them: former material, reinforcement paper, wire, layers, impedance and power.
Getting the diameter right and the heights wrong is a common reason a rebuild fails on reassembly. This guide explains what each dimension controls, how to measure it, and how the six nominal voice coil groups in the UYOman range map to real dimensions.
The three dimensions that define the fit
A voice coil has three fit-critical dimensions:
| Dimension | What it is | How to measure it | What goes wrong |
|---|---|---|---|
| Inside diameter | The bore of the former — the hole the pole piece passes through | Across the former bore, at three points, with calipers | Measuring an expanded old coil or the outside of the winding |
| Former height | Overall height of the former tube, end to end | Along the tube, not around it | Assuming it matches the old part without checking |
| Winding height | Height of the wound section only | From the first turn to the last turn | Including the lead-out or the former above the winding |
Diameter decides whether the coil enters the gap; the two heights decide whether the winding sits in it. A part can pass the first check and still be the wrong part.
Inside diameter: measure the former, not the old coil
Inside diameter is the bore of the former, not the outside diameter of the winding. Use calipers and take three readings around the bore; if the three readings disagree, the former may be out of round or damaged.
The most common error is measuring a coil that has been in service. An overheated former expands, and a coil that was 25.4 mm when new can measure 25.6 mm after a failure. The old part is useful evidence, but it is not the specification. The diameter should be confirmed against the driver, the original drawing or a new part — not only against the coil being replaced.
Do not round a measurement to the nearest inch. A 50.5 mm bore and a 50.8 mm bore sit in the same nominal group, but they are different parts. If the measurement is between catalogue sizes, stop and confirm with a drawing.
Former height and winding height
Former height is the overall length of the former tube from one end to the other. Winding height is the length of the wound section. They are related, but they are not the same number, and both are recorded per variant in the UYOman catalogue.
In the standard range, both measurements are published for each material variant. The 152.2 mm model, for example, uses a 90 mm former height and a 30 mm winding height across its fibreglass and aluminium variants. Smaller models use shorter formers and windings: the 25.5 mm model uses a 35 mm former height and a 14–15 mm winding height.
Height is not cosmetic. The winding needs to sit in the magnetic gap at the height the motor was designed for. If the diameter matches but the former is too long or the winding sits at the wrong point, the coil may not fit under the spider or may not use the gap as intended. A supplier should therefore confirm both values before a replacement is made — not only the bore.
Some suppliers call the former height "total height", and some use total height to mean something else. Ask for the drawing when the terms are ambiguous. A 5 mm difference in height can be the difference between a part that drops in and a part that does not.
The six nominal size groups
Buyers often ask for a "2 inch voice coil", meaning the catalogue group rather than a precise 50.8 mm bore. UYOman groups its 36 voice coil models into six nominal sizes. The table below shows the actual inside diameter range and the variant-level rated power range in each group.
| Nominal group | Inside diameter range | Models | Variant rated power |
|---|---|---|---|
| 1 inch | 25.5–35.5 mm | 3 | 40–100 W |
| 2 inch | 38.4–60.5 mm | 9 | 150–400 W |
| 3 inch | 63.5–87.5 mm | 9 | 200–500 W |
| 4 inch | 89.3–114 mm | 8 | 800–1,500 W |
| 5 inch | 125–135 mm | 4 | 1,800–2,500 W |
| 6 inch | 140–152.2 mm | 3 | 2,500 W |
Across the 36 models, 2-layer windings dominate and 8 Ω is the most common impedance. Four-layer variants and lower-impedance variants are concentrated in the 2-inch and 3-inch groups. Each model carries between two and six material variants, which are listed on the individual product pages.
The power figures are per variant, not per nominal size. The same model can have variants with different rated power because the former material, reinforcement paper and winding details change. Compare the variant, not only the model name.
How to check a replacement before ordering
- Measure the bore of the former at three points and record the actual value in millimetres.
- Record the former height and winding height. Do not infer them from the old part without checking.
- Identify the nominal group, then the exact inside diameter. Do not round across sizes.
- Choose the variant: former material, reinforcement paper, wire, layers, impedance and rated power.
- Confirm the measurement against a drawing or a photo of the original part when possible.
- If the part is not standard, send the dimensions with the application — not only the model name.
The selection logic behind steps 4 and 5 is covered in two related notes: how to choose a voice coil for woofer rebuilds and voice coil former materials. The first explains how power basis and winding choices affect a replacement; the second explains how aluminium, Kapton and fibreglass behave in service.
Standard and custom voice coil options
The table below shows one standard model from each nominal group. It is a map of the range, not a recommendation by size alone: the correct variant depends on the driver and the application.
| Model | Inside diameter | Group | Material variants | Layers | Impedance | Variant rated power |
|---|---|---|---|---|---|---|
| UY-25.5 | 25.5 mm | 1 inch | 4 | 2 | 8 Ω | 40–50 W |
| UY-50.5 | 50.5 mm | 2 inch | 3 | 2 / 4 | 2 / 8 Ω | 180–250 W |
| UY-75.5 | 75.5 mm | 3 inch | 6 | 2 | 8 Ω | 350 W |
| UY-99.2 | 99.2 mm | 4 inch | 5 | 2 | 8 Ω | 900 W |
| UY-125 | 125 mm | 5 inch | 4 | 2 | 8 Ω | 1,800 W |
| UY-152.3 | 152.2 mm | 6 inch | 2 | 2 | 8 Ω | 2,500 W |
Browse the full range, including all 36 models and their variants: Voice Coils.
FAQ
How do I measure the inside diameter correctly? Measure across the former bore with calipers at three points. Do not measure the outside of the winding, and do not rely on an overheated coil in service — a swollen former can read larger than the original part.
What is the difference between former height and winding height? Former height is the overall height of the former tube. Winding height is the height of the wound section only. Both are recorded per variant and both need to match before ordering.
Can I replace a 25.4 mm coil with a 25.5 mm coil? Do not assume interchangeability from a 0.1 mm difference. Measure the actual bore and confirm the former height and winding height. If the measurement is between catalogue sizes, ask for confirmation rather than rounding.
Can you make a non-standard size? Yes — custom voice coils are part of the OEM service. Send the inside diameter, former height, winding height, wire, layers, impedance and a drawing or photo of the original part.
Next step
Record the three dimensions before ordering: inside diameter, former height and winding height. If the values match a standard model, choose the variant by former material, layers and impedance. If they do not, send the measurements and a photo of the old part through OEM & customization and the team will confirm the closest standard coil or what a custom version would require.
Related reading
Most rebuilds fail at the same three points: inside diameter measured wrong, former material chosen by habit, and power handling compared without a test basis.